Shop Mobile More Submit  Join Login
How to make sketchbook. Steps by Piromanova How to make sketchbook. Steps by Piromanova
1. We will need: scissors, cutter, a stack of paper (lol), thick paper for the cover (I chose skrap paper), glue (all-purpose adhesive, the other does not work, I promise), (needle, thread, cloth - for those who want to sew), bandages, double sided tape (but you can use only glue) and clips.

Cut a neat pile of paper or put three folded in half sheets one in one, make a pile of them and clamp our billet with clips.

2. For a simple version (without removing the clips!) You can just glue the back of our billet one time and after it dries another time, preferably smearing glue with fingers (but not in rubber gloves the glue dissolves rubber!).
Complicated version is untranslatable for me.

3. Flyleaf I stick with using double-sided tape. Or the same all-purpose adhesive.

4. Here's what you end up with.

5. I made a markup, where I'll cut (generally get quite exactly XD but since I decided to ....)

6. Now I make the cover. Measure the unit in height and width. Measure out two times, plus space for the thickness (I took about cm). Cut the cover. Then, from the other paper I make the strip and stick to the the spine of the notebook. That will make the back stronger (and generally more aesthetic, lol). Even then I used the curly scissors. The edges of the strip I bent inward.
.
You can make a fabric cover. It is very simple. Measure the height and width of the block. add the 5 mm and cut around two cardboard. For fabric cover you need thinner cardboard or paper. Glue a thin strip of paper(it will be the spine of the notebook ) with two cartons width slightly greater than the thickness of the block. Then dress what we made in cloth, bending the edges inside (here we must be careful. Bookend should "hide" paper) and sticking with the glue.

7. Here's how it looks from the outside (for the spine of the notebook , I just took a block size of the width of paper a little more than 1-2 mm, and noted in pencil. To bend it accurate, I took plastic (iron will tear the paper!) line and passed inside many many times, moving along the other lines on marks.
8, 9. How it looks from inside. I stuck on a bookmark. You can attach it to the paper block too. I attached the corners to strength the edges. Their edges are also doubled in what would be nice.

10. Use glue or double-sided tape I stuck flyleaf to the cover . Now put your notebook under a bunch of books, for example,to perss it good and leave it for a night.

11. We can see that I cut off the edge. This is best done at the stage of cutting the block x)

В общем. для желающих опишу стадии.
1. Нам потребуются: ножницы, резак, стопка бумаги (лол), плотная бумага для обложки (я выбрала скраповскую), клей момент КРИСТАЛЛ (другой не катит, уверяю), (иголка, нитки, тряпка - для желающих сшивать), бинт, двусторонний скотч (можно и клеем обойтись) и прищепки для бумаги (забыла как называются хД)

Нарезаем аккуратную стопочку или делаем "тетради" по три листа и зажимаем прищепками

2. Для простого варианта (не снимая прищепок!) можно просто промазать одну сторону два раза (один раз дав высохнуть и еще раз) клеем КРИСТАЛЛ, желательно, прямо пальцами (ибо если в перчатках резиновых - он растворяет резину!) хорошенько втирая.
Или можно поступить сложнее. С одной стороны приклеиваем бинт и накрываем его полоской бумаги. Сохнет (все это время блок бумаги держится прищепками!). После чего хорошенько натягиваем бинт и приклеиваем его второй полосой бумаги с другой стороны. Теперь, когда высохнет, тонким слоем промазываем клеем получившееся. Теперь можно сшивать. Для начала нужно нанести разметку маркером (на 4 или 6 делений). И потом "протыкать" тетради по разметке. Делать то надо аккуратно. Есть возможность того, что все развалится. Но зато бес специализированных устройств) Сшивать довольно таки просто. Сначала вдеваем нитку со стороны корешка в первую тетрадь. Теперь вдеваем во второе деление рядом. Потом переходим ко второй и так далее, пока не заполнится весь ряд. Затем приступаем ко второму. И так далее. Когда закончите, можно для красоты по краям обклеить лоскутками ткани или же вообще тканевым лейкопластырем (я сделала с отступом потому, что рассчитывала, что буду обрезать неровные части по завершению. а кривости бывают часто, увы х) )

3. Форзац я приклеиваю с помощью двухстороннего скотча. Или же того же КРИСТАЛЛА. ПВА не подойдет!

4. Вот что в итоге получается.

5. Я сделала пометку, как я буду обрезать (вообще получилось довольно ровно XD но, раз уж я решила....)

6. Теперь я делаю обложку. Измеряю блок в высоту и ширину. Отмеряю два раза, плюс место на толщину (у меня около см потребовалось). Вырезаю обложку. Затем из другой бумаги я делаю полосу и приклеиваю к месту корешка (вроде это так называется) для того, что бы корешок был более прочным (и вообще более эстетичным, лол. скраповская бумага некрасиво гнется). Еще тут я использовала фигурные ножницы (вообще они не дорогие, как оказалось. я две штуки приобрела за 65 р). Края полосы загибаю внутрь
.
Так же можно сделать тканевую обложку. Это очень просто. Измеряем высоту и ширину блока. прибавляем по 5 мм где-то и вырезаем две картонки. На место корешка потребуется более тонкая картонка, или бумага. Склеиваем тонкой полосой две картонки шириной чуть больше, чем толщина блока. Затем одеваем это добро в ткань, загибая ее края внутрь (тут надо быть внимательным. форзац должен "прятать" бумагу) и приклеивая моментом.

7. Вот как это выглядит снаружи (что бы красиво согнуть это дело, я просто взяла размер ширины блока бумаги чуть больше на 1-2 мм и отметила карандашом. Затем пластмассовой (железная порвет!) линейкой проходилась изнутри много много раз, двигая вдоль другой линейки по отметкам. Сначала без при клееной полосы, затем с ней)

8, 9. Изнутри это выглядит так. Я приклеила закладку. Можно ее так же и к блоку бумаги прикрепить. Так же сделала уголки для прочности краев. Их края тоже загибаем внутрь, что бы было красиво.

10. С помощью клея или двустороннего скотча приклеиваю одну сторону форзацем к обложке. Когда чуть подсохнет - вторую. Теперь ставим сверху, например, кучу книг, что бы получился пресс.

11. Тут видно, что я срезала края. Это лучше делать на стадии обрезания блока х)
Add a Comment:
 
:iconsammymimi1516:
sammymimi1516 Featured By Owner Jul 17, 2013  Student Traditional Artist
I must try this sometime, it looks fun to try. :D
Reply
:iconthepakshi:
ThePakshi Featured By Owner Oct 1, 2012
Очень здорово! *____*
А на заказ случайно скетчбуки не делаете? ОзО
Reply
:iconpiromanova:
Piromanova Featured By Owner Oct 1, 2012  Student Traditional Artist
делаю) но не дешево)
Reply
:iconthepakshi:
ThePakshi Featured By Owner Oct 1, 2012
Какая примерно стартовая цена?)
Reply
:iconpiromanova:
Piromanova Featured By Owner Oct 1, 2012  Student Traditional Artist
зависит от сложности и размера) самый маленький а6 - 350-400.
Reply
:iconthepakshi:
ThePakshi Featured By Owner Oct 1, 2012
Ок, ясно, спасибо большое за ответ))
Reply
:iconmidnightdestiny04:
MidnightDestiny04 Featured By Owner Sep 15, 2012  Hobbyist General Artist
Wow! This sounds interesting.
I think I'll try this sometime. ^^
Reply
:iconi-am-yaser:
i-am-yaser Featured By Owner Aug 31, 2012  Hobbyist Traditional Artist
очень класно получилось..
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 31, 2012  Student Traditional Artist
спасибо)
Reply
:iconenijoi:
Enijoi Featured By Owner Aug 29, 2012   Digital Artist
оооох! здорово! всегда хотела попробовать но не знала как это делается. спасибище *О*
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 29, 2012  Student Traditional Artist
спасибо) не за что))
Reply
:iconnikkidreamer:
nikkidreamer Featured By Owner Aug 27, 2012  Hobbyist General Artist
I know this is a rough translation but it helps me- this is what google translate spits out when I copy your text. If you know a little english, enough to clarify it any, please do!

In general. for those wishing to describe the stage.
1. We will need: scissors, cutter, a stack of paper (lol), thick paper for the cover (I chose skrapovskuyu), glue point CRYSTAL (the other does not roll, I promise), (needle, thread, cloth - for those who want to sew), bandages, double sided tape (you can do with glue) and paper clips (forgot how is called CD)

Cut a neat pile or do "notebook" on three sheets and clamping clothespins

2. For a simple version (without removing the clothespins!) You can just fluff one side twice (once and letting it dry again) Crystal glue, preferably right fingers (because if the rubber gloves - it dissolves rubber!) Good rubbing.
Or, you can do more complicated. On the one hand stick bandage and cover it with a strip of paper. Dry (all the while holding a block of paper pegs!). After that, a good stretch the bandage and stick it on the second strip of paper with the other hand. Now, when dried, a thin layer of glue promazyvayut to get. Now you can sew. First you need to apply markup marker (for 4 or 6 points). And then "poke" notebooks on the markup. Do you have to care. There is a possibility that all fall apart. But the devil of specialized devices) are joined pretty simple. Vdevaem first thread of the spine in the first book. Vdevaem now in the second division side. Then move to the second and so on, until it fills the entire row. Then proceed to the second. And so on. When you're done, you beauty on the edges pasted scraps of fabric or any fabric adhesive tape (I made indented because hoped that I would be the rough cut of the completion. Krivosti and are often, alas x))

3. Flyleaf I stick with using double-sided tape. Or the same crystal. PVA will not work!

4. Here's what you end up with.

5. I made a note, I'll cut (generally get quite exactly XD but since I decided to ....)

6. Now I make the cover. Measure the unit in height and width. Measure out two times, plus space for the thickness (I took about cm). Cut the cover. Then, from the other paper I make the strip and stick to the site root (like the so called) for what would have been back stronger (and generally more aesthetic, lol. Skrapovskaya paper ugly oppression). Even then I used the curly scissors (they are not expensive at all, as it turned out. I bought two pieces for 65 p.) Edge of the double in
.
You can make a fabric cover. It is very simple. Measure the height and width of the block. add the 5 mm and cut around two cardboard. In place of the spine require thinner cardboard or paper. Glue a thin strip of two cartons width slightly greater than the thickness of the block. Then the dress is good in cloth, bending the edges inside (here we must be careful. Bookend should "hide" paper) and sticking point.

7. Here's how it looks from the outside (that would be nice to bend this thing, I just took a block size of the width of paper a little more than 1-2 mm, and noted in pencil. Then plastic (iron will break!) Line passes inside many many times, moving along the other lines on marks. glued at first without the band, and then with her)

8, 9. From the inside it looks like. I'm stuck on a bookmark. Can it be the same and attach the paper to the block. Just made the corners for strength edges. Their edges are also double in what would have been nice.

10. Use glue or double-sided tape is glued to one side of the bookend cover. When nearly dry up - the second. Now put the top, for example, a bunch of books to get press.

11. We can see that I cut off the edge. This is best done at the stage of cutting block x)
Reply
:iconknightmonx:
knightmonx Featured By Owner Aug 27, 2012  Student General Artist
thank you for translating it also, a llama for you too! ;3
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 27, 2012  Student Traditional Artist
you amazing O_o
Reply
:iconnikkidreamer:
nikkidreamer Featured By Owner Aug 27, 2012  Hobbyist General Artist
I think I understand most of it from the visuals! They are very clear photographs. Is that just gauze glued to the folded sides for the binding?
Reply
:iconnikkidreamer:
nikkidreamer Featured By Owner Aug 27, 2012  Hobbyist General Artist
Oh, and what is the purpose of the yellow tape? Is that just to reinforce the cover? Did you put some on the back cover too?
Reply
:iconnikkidreamer:
nikkidreamer Featured By Owner Aug 27, 2012  Hobbyist General Artist
nevermind! after I put it through the google translator, I see that it is double sided tape for your cover paper! Great idea. Glue is so messy and often makes it bubble or uneven.
Reply
:iconvampiii:
Vampiii Featured By Owner Aug 27, 2012  Professional Digital Artist
I'm not sure of the translation but i hope it helps :)
Reply
:iconvampiii:
Vampiii Featured By Owner Aug 27, 2012  Professional Digital Artist
1. We will need: scissors, cutter, a stack of paper (lol), thick paper for the cover (I chose skrap paper), glue (all-purpose adhesive, the other does not work, I promise), (needle, thread, cloth - for those who want to sew), bandages, double sided tape (but you can use only glue) and clips.

Cut a neat pile of paper or put three folded in half sheets one in one, make a pile of them and clamp our billet with clips.

2. For a simple version (without removing the clips!) You can just glue the back of our billet one time and after it dries another time, preferably smearing glue with fingers (but not in rubber gloves – the glue dissolves rubber!).
Complicated version is untranslatable for me.

3. Flyleaf I stick with using double-sided tape. Or the same all-purpose adhesive.

4. Here's what you end up with.

5. I made a markup, where I'll cut (generally get quite exactly XD but since I decided to ....)

6. Now I make the cover. Measure the unit in height and width. Measure out two times, plus space for the thickness (I took about cm). Cut the cover. Then, from the other paper I make the strip and stick to the the spine of the notebook. That will make the back stronger (and generally more aesthetic, lol). Even then I used the curly scissors. The edges of the strip I bent inward.
.
You can make a fabric cover. It is very simple. Measure the height and width of the block. add the 5 mm and cut around two cardboard. For fabric cover you need thinner cardboard or paper. Glue a thin strip of paper(it will be the spine of the notebook ) with two cartons width slightly greater than the thickness of the block. Then dress what we made in cloth, bending the edges inside (here we must be careful. Bookend should "hide" paper) and sticking with the glue.

7. Here's how it looks from the outside (for the spine of the notebook , I just took a block size of the width of paper a little more than 1-2 mm, and noted in pencil. To bend it accurate, I took plastic (iron will tear the paper!) line and passed inside many many times, moving along the other lines on marks.
8, 9. How it looks from inside. I stuck on a bookmark. You can attach it to the paper block too. I attached the corners to strength the edges. Their edges are also doubled in what would be nice.

10. Use glue or double-sided tape I stuck flyleaf to the cover . Now put your notebook under a bunch of books, for example,to perss it good and leave it for a night.

11. We can see that I cut off the edge. This is best done at the stage of cutting the block x)
Reply
:iconnikkidreamer:
nikkidreamer Featured By Owner Aug 27, 2012  Hobbyist General Artist
awesome! even clearer than the auto translate from google. Thanks! <3
Reply
:iconvampiii:
Vampiii Featured By Owner Sep 6, 2012  Professional Digital Artist
I hope so!! :hug:
Reply
:iconknightmonx:
knightmonx Featured By Owner Aug 27, 2012  Student General Artist
thanks for making it English! llama for you!
Reply
:iconvampiii:
Vampiii Featured By Owner Sep 6, 2012  Professional Digital Artist
Thank you for the llama )
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 27, 2012  Student Traditional Artist
em... sorry. just a minute! I try to read it and translate! I hope my friend will help me)
Reply
:iconsparr0wlicious:
Sparr0wlicious Featured By Owner Aug 27, 2012  Hobbyist General Artist
Um ... maybe someone could try to translate it? this looks really interesting but I have no idea what's going on. /:
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 28, 2012  Student Traditional Artist
1. We will need: scissors, cutter, a stack of paper (lol), thick paper for the cover (I chose skrap paper), glue (all-purpose adhesive, the other does not work, I promise), (needle, thread, cloth - for those who want to sew), bandages, double sided tape (but you can use only glue) and clips.

Cut a neat pile of paper or put three folded in half sheets one in one, make a pile of them and clamp our billet with clips.

2. For a simple version (without removing the clips!) You can just glue the back of our billet one time and after it dries another time, preferably smearing glue with fingers (but not in rubber gloves – the glue dissolves rubber!).
Complicated version is untranslatable for me.

3. Flyleaf I stick with using double-sided tape. Or the same all-purpose adhesive.

4. Here's what you end up with.

5. I made a markup, where I'll cut (generally get quite exactly XD but since I decided to ....)

6. Now I make the cover. Measure the unit in height and width. Measure out two times, plus space for the thickness (I took about cm). Cut the cover. Then, from the other paper I make the strip and stick to the the spine of the notebook. That will make the back stronger (and generally more aesthetic, lol). Even then I used the curly scissors. The edges of the strip I bent inward.
.
You can make a fabric cover. It is very simple. Measure the height and width of the block. add the 5 mm and cut around two cardboard. For fabric cover you need thinner cardboard or paper. Glue a thin strip of paper(it will be the spine of the notebook ) with two cartons width slightly greater than the thickness of the block. Then dress what we made in cloth, bending the edges inside (here we must be careful. Bookend should "hide" paper) and sticking with the glue.

7. Here's how it looks from the outside (for the spine of the notebook , I just took a block size of the width of paper a little more than 1-2 mm, and noted in pencil. To bend it accurate, I took plastic (iron will tear the paper!) line and passed inside many many times, moving along the other lines on marks.
8, 9. How it looks from inside. I stuck on a bookmark. You can attach it to the paper block too. I attached the corners to strength the edges. Their edges are also doubled in what would be nice.

10. Use glue or double-sided tape I stuck flyleaf to the cover . Now put your notebook under a bunch of books, for example,to perss it good and leave it for a night.

11. We can see that I cut off the edge. This is best done at the stage of cutting the block x)
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 27, 2012  Student Traditional Artist
my English is so bad! T______T I can't translate it. sorryyyyyy! may be [link] can help you?
Reply
:iconfires-storm:
Fires-storm Featured By Owner Aug 27, 2012  Student General Artist
Very cool, wanted to try something like this!
Reply
:iconellen-tao:
Ellen-Tao Featured By Owner Aug 25, 2012  Hobbyist Digital Artist
Как интересно!
Может быть, как-нибудь попробую **
Reply
:iconvanilla-rai:
Vanilla-Rai Featured By Owner Aug 25, 2012  Student Traditional Artist
О,я тоже ими занимаюсь,только по другому делаю,совсем о.о
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 25, 2012  Student Traditional Artist
а как?
Reply
:iconvanilla-rai:
Vanilla-Rai Featured By Owner Aug 25, 2012  Student Traditional Artist
Ну,не совсем по-другому.Я сначала сшиваю.Потом проклеиваю титаном и ложу под пресс. Потом приклеиваю марлю/бинт,под пресс. Обрезаю. Обложку делаю из 3-х кусков картона. 2 одинаковых по ширине-длине листов и 1 узкий для корешка. Обтягиваю их тканью или картоном и приклеиваю к форзацам.Всё о.о
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 25, 2012  Student Traditional Artist
похоже в целом)
Reply
:iconvanilla-rai:
Vanilla-Rai Featured By Owner Aug 25, 2012  Student Traditional Artist
Ага,попробую потом вашим методом?сами придумали или тутр какой еще есть?<3
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 25, 2012  Student Traditional Artist
до большинства фишек сама дошла. а в остальном надоумило место учебы)
Reply
:iconvanilla-rai:
Vanilla-Rai Featured By Owner Aug 26, 2012  Student Traditional Artist
ясно,а где учитесь?
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 26, 2012  Student Traditional Artist
на художника) у нас на курсе был предмет "шрифты". там мы проходили как делать переплеты)
Reply
(1 Reply)
:iconprzhk:
przhk Featured By Owner Aug 25, 2012  Hobbyist General Artist
шикарно~ я вас люблю, особенно за детальное объяснение XD
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 25, 2012  Student Traditional Artist
О_о да не за что. наверняка лучше есть туты) но я рада, если вам нравится ^____^
Reply
:iconchornayadrakoshig:
ChornayaDrakoshig Featured By Owner Aug 25, 2012  Hobbyist General Artist
Здорово ^^
Но мне было бы жалко такую красотень на рисунки переводить Т_Т
Я обхожусь пачкой листов в клетку, надраных со старых тетрадей)))
Reply
:iconpiromanova:
Piromanova Featured By Owner Aug 25, 2012  Student Traditional Artist
ну можно так сшивать и простую бумагу) вообще это значительно дешевле выходит, чем покупать специально скетчбуки, альбомы и пр)
Reply
Add a Comment:
 
×




Details

Submitted on
August 25, 2012
Image Size
3.2 MB
Resolution
1500×12336
Link
Thumb
Embed

Stats

Views
4,322
Favourites
225 (who?)
Comments
42
Downloads
50

Camera Data

Make
Canon
Model
Canon PowerShot A3000 IS
Shutter Speed
1/30 second
Aperture
F/2.7
Focal Length
6 mm
ISO Speed
125
Date Taken
Mar 22, 2012, 10:19:30 AM
Software
Adobe Photoshop CS5 Windows
Sensor Size
2mm
×